Euromicron Mould Engineering Limited was found in 1995

Euromicron Mould  >  AI - Page Sitemap  >  quick delivery plastic enclosure box by wholesale for andon electronics
quick delivery plastic enclosure box by wholesale for andon electronics

quick delivery plastic enclosure box by wholesale for andon electronics
  • quick delivery plastic enclosure box by wholesale for andon electronics
  • quick delivery plastic enclosure box by wholesale for andon electronics
  • quick delivery plastic enclosure box by wholesale for andon electronics

quick delivery plastic enclosure box by wholesale for andon electronics

Based in China, Euromicron Mould Engineering Limited mainly manufactures and distributes plastic enclosures for electronics . We are becoming famous in the international market.
Inquire Online
Get the latest price
Quantity Needed:
Pieces
E-mail:
Product Comparison
die casting mold is in line with the stringent quality standards. The price is more favorable than other products in the industry and the cost performance is relatively high.The products we produce are in strict line with the . Their high quality is guaranteed through reliable material sourcing and strict QC methods.Compared with other products in the same category, die casting mold has more advantages, specifically in the following aspects.
  • v s
Enterprise Strength
  • Our excellence comes from the efforts of staff from such departments as R&D department, sales department, design department and production department. There are designers, R&D experts, and after-sales personnel in our company.
  • Euromicron always put customers first and provides them with sincere and quality services.
  • Euromicron always sticks to our tenet of "quality comes first" by focusing on the quality control, service improvement, and fast response.
  • We have been dedicated to the manufacturing of cnc service for about years, and have become the leading enterprise in the industry. This enables us to introduce and operate a complete set of production equipment, and achieve intelligentization and standardization.
  • Since the establishment, our sales network has been continuously expanding to where our sales service is highly appraised by customers at home and abroad. In future, we would like to establish our marketing network overseas and expand the business further.
Company Advantages
1. The selection of plastic enclosures for electronics depends on the quality of plastic enclosure box to a large extent.
2. The wide used foreground of plastic enclosure box is proved over a long period of time.
3. If you are not confident enough in our quality of plastic enclosure box, we can send free samples for testing first.


Part Name:Gateway
Part size:175*136*32mm
Raw Material:ABS+PC
Color:RAL9010,White
Mould Cavity No.:1*1
Injection gate:Hot runner with pin point gate
Surface finished: Mirror Polishing
Core &Cavity steel:1.2344,hardness 48~52HRC
Mold component standard:HASCO or equivalent
Injection machine size:180T
Cycle time:35S
Mold life:300000 shots
Customer:HEKATR@N
Export:Germany


◇◆ Summary for project running
This product used for electrical appliance,the gateway case and grid.Plastic raw material need in inflaming retarding and heat resistant.
quick delivery plastic enclosure box by wholesale for andon electronics-1

We carried out first trial shot on 40th day,little longer than planed.Since YUDO hot runner system came out of expected date,one week late.Three trial shots for samples production,and finished whole project in 50days.Manufacture schedule,samples delivery and mold shipment date ran as planing,within customer’s request.
Both parts critical surface need in high polishing,mirror grade,no any marked or scratch allowed.When production,have to take out by robot hand,and cover PE film for protection. Silkscreen also made by EMM factory.

quick delivery plastic enclosure box by wholesale for andon electronics-2

At first trial shot,case part came out with obvious sink mark and scratch on side surface. The ribs inside are too thick cause sink mark,and no draft angle on side surface cause scratch when mold open.Finally We cut rib material solved sink mark problem.But no draft angle allowed on side surface,we had to add two sliders on both side,to ensure all outside surface look glossy.
The grid part has many small window and only 0.6mm thick.We found flowing mark at each window corner and short shot problem at first trial shot.Then we suggested change high polishing surface to fine texture,VDI3400-33,also change injection gate location,from both side for filling.Customer confirmed and part came out look good.




Company Features
1. Based in China, Euromicron Mould Engineering Limited mainly manufactures and distributes plastic enclosures for electronics . We are becoming famous in the international market.
2. Euromicron Mould Engineering Limited has professional technical personnel to undertake plastic enclosure box solutions.
3. In order to better improve sustainability, we have newly introduced a green production approach. This approach has significantly promoted the reuse and recycling of raw materials and packaging materials, which reduces resource wastes. We aim to set up a diverse and inclusive workforce team and values individuals and their contribution. This allows us to better serve our customers. Our customers are at the heart of everything we do. We design products that they need, and we listen carefully to their voices to understand their specific requirements. We promise all of our business activities are conform to the legal statutes of China. We'll never produce unlicensed products or infringe copyrights.
plastic enclosures for electronics is various in different styles. It is manufactured to the standards such as EN 60825
The production method of Euromicron Mould plastic enclosures for electronics is improved combining the newest technology. It always receives attention at exhibitions such as Indonesia industrial machinery and electronic products exhibition
Euromicron Mould plastic enclosures for electronics is appealing with its unique appearance. It uses components from international manufacturers, such as Panasonic Japan (servo motors and drives
Euromicron Mould has experienced design team to design the appearance of plastic enclosures for electronics. It ensures the materials being cut have smooth edges
As we all know, Euromicron Mould boasts its excellent design for plastic enclosures for electronics. It can achieve a manufacturing precision of 0.05 mm
Before tapping into the market, it must pass the scientific test. It is compatible with software such as CAD or Adobe
Product Message
Chat Online 编辑模式下无法使用
Chat Online inputting...