loading

Euromicron Mould Engineering Limited was found in 1995

Home  >  Customized Application  >  Electrommunication For sell  >  overmolding electronics electronics for electronic components Euromicron Mould
overmolding electronics electronics for electronic components Euromicron Mould

overmolding electronics electronics for electronic components Euromicron Mould

Product Name
Electronic connector
Product size
35*29.5*26mm
Material
PA9T30GF
Cavity
1*4
Cycle time
40S
Customer
Bitron
Export
Italy
Product Comparison
Euromicron carefully selects quality raw materials. Production cost and product quality will be strictly controlled. This enables us to produce die casting mold which is more competitive than other products in the industry. It has advantages in internal performance, price, and quality.The products we produce are in strict line with the . Their high quality is guaranteed through reliable material sourcing and strict QC methods.After being improved greatly, Euromicron's die casting mold is more advantageous in the following aspects.
Company Advantages
1. The modern manufacture technology guarantees the production of Euromicron Mould overmolding electronics .
2. It has good hand characteristics which include thickness compressibility, plane compressibility, flexibility self flex, resistance flex, maintenance flex, and reflex.
3. The price of this product is quite competitive and is widely available in the market.
4. The product is priced at a rather competitive price and is widely demanded in the market.


This connector was supposed to be molded in glass-fiber-reinforced,flame-retardant nylon.
It came with size 35X29.5X26mm,with 40pcs pins in center.High rib,hooks and boss on round side.One four cavity mold should employ a mold base dimension 250*230mm,with 280mm height.Steel grade 1.2767 is used for the mold inserts,while grade 1.2312 is employed for mold plates as well as the ejector plate.Steel grade 1.1730 is mused for remaining plate and rails.Thermal insulating plates,which are available in sizes to match the standard mold plates,serve to insulate the mold from the machine platens.



◇◆ Mold design


This part is simple,but need to ensure 40pcs pin locate properly when plastic filling,specially under high pressure flow.To save production cost,we need to cut down cycle time.So two or three even more over-mold inserts need.Injection machine operator no need to set pin one by one into mold.Just need to set in additional insert before molding.When mold open,just need put whole insert with pin into core.Of course,operator need to take part with insert together.The hooks on both sides are undercut,need design for slider or angle lifter.But no slider split line allow in middle surface.So split line should be set on radius of corner.

The molded part is ejected via knockout pins.In addition to providing for ejection.these pins serve to vent the cavity during filling.It is in part for this reason that the knockout pins are located beneath ribs and other deep section of the part.where entrapped air is to be expected.The mold filling pattern during injection of the molding compound as well as the mechanical and thermal aspects of the mold design were simulated and established during the design phase with the aid of appropriate computer programs.



Company Features
1. With its highly advanced equipment, Euromicron Mould has been the leading position of electronic parts market.
2. Our factory has imported a series of advanced production facilities that can ensure constant and steady production. This means that thousands of products can be made in astonishingly short periods of time.
3. Euromicron Mould Engineering Limited strive to achieve continuous improvement on plastic prototype . Get info! We have high-performance work teams. They can execute quickly, make reliable decisions, solve complex problems, and spare efforts to increases company productivity and morale. Sustainability and corporate social responsibility initiatives are going to be implemented strictly by the company in the coming years. By improving the operation ways and production process, we plan to lower the cost of operation and benefit the society by using fewer resources. Get info!

ODS Pilot burner
1.Material:Brass
2.Air supplier:Gas
3.Used in gas range oven,gas heater with oxygen depletion sensor

ODS Pilot burner

Burner,ODS pilot-burnerworks as ignition part for gas applicance,such as BBQ grill,stoves,heaters,fireplace etc.

Suitable to NG and LPG

not only save energy,but protect environmental.

pressure of gas:25-30 Mbar

Gas flow:7.5e/h en air at 50 Mbar

Power:145W at 30 Mbar

The pilot flame of the ODS system is in contact with the ODS thermocouple that generates the necessary millivoltage needed to hold the solenoid safety valve inside of the control valve in the open position.The ODS safetu valve is a "Spring-Loaded Normally Closed" valve.

The safety valve closes causing the gas supply to the vent-free gas product to be cut off. The appliance shuts down.It is important to understand that the ODS sysytem does not sense carbon monoxide directly.it responds to a reduction of oxygen of oxygen in the area of the appliance.

FAQ

  FAQ  

 

1.can you make customized designed products?
Yes,we are factory,and can make the products According to your requirements, like the shape,size,color,
logo and other details.
2.how to know the item price?
If the products you want are showing on our website or on the picture album,you just tell us 
the item No.and your quantity, i will give you the besr price.
If the products need your personal designs and requirements,please tell us the following
information so that we can offer the price immediately.
1) model and measure of the products(you had better have drawings,samples or product photos).
(HD Pixel source file,  PSD    CDR    AI   JPEG  will be better).
2) quantity and expected time for delivery.
3) if you need sandblasting and inner sculpture,please inform us at the same time.
4) your detailed contact method.
  Notes: Generally speaking,our prices include the Tax for common Gift boxes if there are
no such requirements,please inform us beforehand.
3.what is the minimum order quantity you want?
Normally, there is NO Limit for the minimum order quantity. the minimum order quantity is 
subject to the demand of our esteemed clients.more bigger quantity,the price is also more 
cheaper.
4.what is your principle for the samples?
We can deliver common samples worth not too much if customers are willing to pay the shipping charges. if samples are made on basis of customers’ needs,we will ask for the samples fees only if we receive the order from you. if samples involving laser inner sculpture,we will ask some design charges from your side.
5.normally,how long will it last before delivery?
As usual,one week is enough after your order to deliver your goods, but for some gifts with small quantity and less complicated crafts,we can deliver earlier before the deadline.if customers need urgent orders, we can negotiate the time for delivery but you have to pay some extra expenses.
6.what is the common means of shipping normally?
Normallu, we send samples by Express,but for the order,we use many ways.
if total weight is less than 100kg, we suggeat that choose Express.
if total weight is 100kg to 500kg, we suggeat that choose Air shipping.
if total weight is over 500kg, we suggeat that choose Sea shipping.
but if your time is urgent, we could discuss together,choose the beat.
7.which payment can be acceptable? and how to do it?
We could accpet the payment be T/T,Western Union and Alipay, for the sample fee, customer should pay in full. for the mass order, customer should pay 40%deposit, the balance should be paid before shipment.
When customer do the payment, may have a little bank charge, customer should bear this. 
 
Chat Online 编辑模式下无法使用
Leave Your Message inputting...