Euromicron Mould Engineering Limited was found in 1995

Euromicron Mould  >  AI - Page Sitemap  >  high productivity electronic parts siemens supplier for electronic components
high productivity electronic parts siemens supplier for electronic components

high productivity electronic parts siemens supplier for electronic components
  • high productivity electronic parts siemens supplier for electronic components
  • high productivity electronic parts siemens supplier for electronic components
  • high productivity electronic parts siemens supplier for electronic components
  • high productivity electronic parts siemens supplier for electronic components
  • high productivity electronic parts siemens supplier for electronic components

high productivity electronic parts siemens supplier for electronic components

In the design of Euromicron Mould overmolding electronics, there are some steps involved, including assessment of water quality, desired treated water quality, selection of the treatment process, and system design. Situated in Foshan city of China, our factory covers an area of 2,000 square meters
Get the latest price
Quantity Needed:
Pieces
E-mail:


high productivity electronic parts siemens supplier for electronic components-1
high productivity electronic parts siemens supplier for electronic components-2


◇◆ Product parameters


Part Name:Electronic connector
Part size:45*39.5*21mm
Raw Material:PA9T30GF
Color:RAL9005,Black
Mould Cavity No.:1*4
Injection gate:Hot runner 
Surface finished: VDI3400-33
Core &Cavity steel:1.2344,hardness 48~52HRC
Mold component standard:HASCO or equivalent
Injection machine size:250T
Cycle time:40S
Mold life:100000 shots
Customer:Bitron
Export:Italy


◇◆ PRODUCT FEATURES
A connector shell was supposed to be molded in glass-fiber-reinforced,flame-retardant nylon.
high productivity electronic parts siemens supplier for electronic components-3

This connector include two different parts(upper and lower halves),were to be produced in a single mold.Prior to the start of production,the question arose as to whether a second gate might not be required to fill the part.To avoid weld lines and entrapped air.however,it might also be necessary to use only a single gate.This flexibility as to gating was supposed to be possible simple by switching a hot runner nozzle on or off.A further difficulty resulted from the small amount of space in which  the gates were to be located on the face of the molded part.All of these requirements were satisfied through the particular arrangement of the conductive,internally heated hot-runner system.

high productivity electronic parts siemens supplier for electronic components-4

Mold design-We made this mold with four cavity.Runner system consists of a heated sprue bushing,a hot-runner manifold and four hot-runner nozzles.The hot-runner nozzles have not been installed parallel to the longitudinal axis of the mold,but rather at an angle.In spite of the unfavorable geometric relationships,it is possible to gate each part on its face in this manner.This arrangement is possible,because the solidified melt in the outer regions of the hot-runner manifold and nozzle channels precludes any possibility of leakage.Each of the hot-runner nozzle is individually controlled and can thus be switched on or off as required.It is thus possible to fill the part through either on or two gates.These measures alone,however,would not have been adequate to vary the gating possibilities.Attention also have to be given to the hot-runner manifold to ensure that no melt stagnated at continuously high temperatures in the runner channels when the various gating possibility were being employed.




Euromicron Mould overmolding electronics is designed with a scientific system. This system includes a sterilization system to reliably supply the desired water quality. Different from traditional decking tiles, we use high-quality plastic base and all types of surface materials
The purifying system of Euromicron Mould overmolding electronics has been built using standardized 'building block' methods, allowing for quick delivery and installation. There are over 13 series and 200 items available for our decking tiles
Euromicron Mould overmolding electronics has to go through a comprehensive QC check including the performance of filter and membrane, PLC controller, and valves. All our decking tiles have conducted strict tests
The production of Euromicron Mould electronic parts is constantly monitored. For example, its production is conducted in a microbiologically controlled environment. Every piece of product has to go through material checking, DUPRO, double QC checking
Euromicron Mould overmolding electronics has been evaluated regarding the safety construction such as instrumentation and control, electrical and mechanical equipment, mechanical and structural piping, supports and hangers, etc. Staff working in Jiabang are all well-trained
It is in high accordance with the quality inspection standards. Different from traditional decking tiles, we use high-quality plastic base and all types of surface materials
Product Message
Chat Online 编辑模式下无法使用
Chat Online inputting...