Euromicron Mould Engineering Limited was found in 1995

Euromicron Mould  >  AI - Page Sitemap  >  high productivity electronic parts connector supplier for andon electronics
high productivity electronic parts connector supplier for andon electronics

high productivity electronic parts connector supplier for andon electronics
  • high productivity electronic parts connector supplier for andon electronics
  • high productivity electronic parts connector supplier for andon electronics
  • high productivity electronic parts connector supplier for andon electronics
  • high productivity electronic parts connector supplier for andon electronics
  • high productivity electronic parts connector supplier for andon electronics

high productivity electronic parts connector supplier for andon electronics

The production of Euromicron Mould electronic parts uses high technology. And the technology we used is constantly updated, the packaging capacity is always guaranteed. It will automatically shut down to prevent the generated energy from harming people when there is a blackout
Inquire Online
Get the latest price
Quantity Needed:
Pieces
E-mail:


high productivity electronic parts connector supplier for andon electronics-1
high productivity electronic parts connector supplier for andon electronics-2


◇◆ Product parameters


Part Name:Electronic connector
Part size:45*39.5*21mm
Raw Material:PA9T30GF
Color:RAL9005,Black
Mould Cavity No.:1*4
Injection gate:Hot runner 
Surface finished: VDI3400-33
Core &Cavity steel:1.2344,hardness 48~52HRC
Mold component standard:HASCO or equivalent
Injection machine size:250T
Cycle time:40S
Mold life:100000 shots
Customer:Bitron
Export:Italy


◇◆ PRODUCT FEATURES
A connector shell was supposed to be molded in glass-fiber-reinforced,flame-retardant nylon.
high productivity electronic parts connector supplier for andon electronics-3

This connector include two different parts(upper and lower halves),were to be produced in a single mold.Prior to the start of production,the question arose as to whether a second gate might not be required to fill the part.To avoid weld lines and entrapped air.however,it might also be necessary to use only a single gate.This flexibility as to gating was supposed to be possible simple by switching a hot runner nozzle on or off.A further difficulty resulted from the small amount of space in which  the gates were to be located on the face of the molded part.All of these requirements were satisfied through the particular arrangement of the conductive,internally heated hot-runner system.

high productivity electronic parts connector supplier for andon electronics-4

Mold design-We made this mold with four cavity.Runner system consists of a heated sprue bushing,a hot-runner manifold and four hot-runner nozzles.The hot-runner nozzles have not been installed parallel to the longitudinal axis of the mold,but rather at an angle.In spite of the unfavorable geometric relationships,it is possible to gate each part on its face in this manner.This arrangement is possible,because the solidified melt in the outer regions of the hot-runner manifold and nozzle channels precludes any possibility of leakage.Each of the hot-runner nozzle is individually controlled and can thus be switched on or off as required.It is thus possible to fill the part through either on or two gates.These measures alone,however,would not have been adequate to vary the gating possibilities.Attention also have to be given to the hot-runner manifold to ensure that no melt stagnated at continuously high temperatures in the runner channels when the various gating possibility were being employed.




The design of Euromicron Mould custom plastic cases for electronics involves several stages. They are trend studies, fabric and accessory research, sample making, etc. The product maintains the balance between the two types of energy involved in powering the appliances
The tests for Euromicron Mould custom plastic cases for electronics have been conducted. These tests include wiring of main control cabinets, including PLC wiring and operator stations. It will automatically shut down to prevent the generated energy from harming people when there is a blackout
The production process of Euromicron Mould electronic parts covers the following stages. They are materials receiving, materials cutting, molding, component fabricating, parts assembling, and finishing. All these processes are conducted by professional technicians with years of experience in upholstery. The product maintains the balance between the two types of energy involved in powering the appliances
The manufacture of Euromicron Mould electronic parts is divided into a few aspects. They are mainly materials preparation, mechanical components' cleaning, cutting, milling, welding, and parts assembly. The product offers outstanding user-friendliness and very good exploitation of the energy available
Euromicron Mould custom plastic cases for electronics has passed a series of security tests. It has been tested the electric strength test, also known as high-voltage insulation test, water-resistant test, and tests for potential overload and statics. With the circuit protection function, its components such as fuse are not easily burned out
The product has stable performance, long storage life and reliable quality. The commercial-grade design makes it suitable for long periods of continuous operation
Product Message
Chat Online 编辑模式下无法使用
Chat Online inputting...