Euromicron Mould Engineering Limited was found in 1995

Euromicron Mould  >  AI - Page Sitemap  >  high efficiency plastic case for electronics connector wholesale for andon electronics
high efficiency plastic case for electronics connector wholesale for andon electronics

high efficiency plastic case for electronics connector wholesale for andon electronics
  • high efficiency plastic case for electronics connector wholesale for andon electronics
  • high efficiency plastic case for electronics connector wholesale for andon electronics
  • high efficiency plastic case for electronics connector wholesale for andon electronics
  • high efficiency plastic case for electronics connector wholesale for andon electronics
  • high efficiency plastic case for electronics connector wholesale for andon electronics

high efficiency plastic case for electronics connector wholesale for andon electronics

Euromicron Mould plastic case for electronics has been tested according to the general standards. It is tested in terms of functionality, strength, stiffness, wears, and corrosion. Our company has successfully got several patents for technology
Get the latest price
Quantity Needed:
Pieces
E-mail:


high efficiency plastic case for electronics connector wholesale for andon electronics-1
high efficiency plastic case for electronics connector wholesale for andon electronics-2


◇◆ Product parameters


Part Name:Electronic connector
Part size:45*39.5*21mm
Raw Material:PA9T30GF
Color:RAL9005,Black
Mould Cavity No.:1*4
Injection gate:Hot runner 
Surface finished: VDI3400-33
Core &Cavity steel:1.2344,hardness 48~52HRC
Mold component standard:HASCO or equivalent
Injection machine size:250T
Cycle time:40S
Mold life:100000 shots
Customer:Bitron
Export:Italy


◇◆ PRODUCT FEATURES
A connector shell was supposed to be molded in glass-fiber-reinforced,flame-retardant nylon.
high efficiency plastic case for electronics connector wholesale for andon electronics-3

This connector include two different parts(upper and lower halves),were to be produced in a single mold.Prior to the start of production,the question arose as to whether a second gate might not be required to fill the part.To avoid weld lines and entrapped air.however,it might also be necessary to use only a single gate.This flexibility as to gating was supposed to be possible simple by switching a hot runner nozzle on or off.A further difficulty resulted from the small amount of space in which  the gates were to be located on the face of the molded part.All of these requirements were satisfied through the particular arrangement of the conductive,internally heated hot-runner system.

high efficiency plastic case for electronics connector wholesale for andon electronics-4

Mold design-We made this mold with four cavity.Runner system consists of a heated sprue bushing,a hot-runner manifold and four hot-runner nozzles.The hot-runner nozzles have not been installed parallel to the longitudinal axis of the mold,but rather at an angle.In spite of the unfavorable geometric relationships,it is possible to gate each part on its face in this manner.This arrangement is possible,because the solidified melt in the outer regions of the hot-runner manifold and nozzle channels precludes any possibility of leakage.Each of the hot-runner nozzle is individually controlled and can thus be switched on or off as required.It is thus possible to fill the part through either on or two gates.These measures alone,however,would not have been adequate to vary the gating possibilities.Attention also have to be given to the hot-runner manifold to ensure that no melt stagnated at continuously high temperatures in the runner channels when the various gating possibility were being employed.




The creation of Euromicron Mould plastic case for electronics involves some advanced technologies. They include mechanical systems technology, automatic control technology, sensing technology, and servo-drive technology. We have a top R&D team to keep improving quality and design for our decking tiles
Euromicron Mould plastic case for electronics is designed with consideration of all possible mechanisms. These mechanisms are aimed at helping the desired motion or the group of motions in this product. Our good products win us many distinguished customers, such as Build Direct in US, Clas Olhson in Sweden
The design of Euromicron Mould plastic case for electronics is born with many considerations. They are aesthetic, ease of handling, operator safety, force/stress analysis, etc. Our factory has already passed BSCI/Disney audit
There are many important considerations in the design of Euromicron Mould plastic case for electronics. They are the type of load and stresses caused by the load, motion of parts, form and size of the parts, etc. Our good products win us many distinguished customers, such as Build Direct in US, Clas Olhson in Sweden
The design of Euromicron Mould plastic case for electronics is strictly conducted. It is carried out by our designers who think highly of parts and components safety, the whole machine safety, operation safety, and environmental safety. We have a top R&D team to keep improving quality and design for our decking tiles
This product is eco-friendly and generates no waste. Some parts used in it are recycled materials, maximizing the use of useful and available materials. We export our products to many countries, including Japan, US, Middle East and etc
Product Message
Chat Online 编辑模式下无法使用
Chat Online inputting...