Euromicron Mould Engineering Limited was found in 1995

Euromicron Mould  >  AI - Page Sitemap  >  high efficiency electronic parts electronic customized for andon electronics
high efficiency electronic parts electronic customized for andon electronics

high efficiency electronic parts electronic customized for andon electronics
  • high efficiency electronic parts electronic customized for andon electronics
  • high efficiency electronic parts electronic customized for andon electronics
  • high efficiency electronic parts electronic customized for andon electronics
  • high efficiency electronic parts electronic customized for andon electronics

high efficiency electronic parts electronic customized for andon electronics

Euromicron Mould injection molded electronics meets the requirements of a series of standards. These standards include IEC 60038 (IEC standard voltages), IEC 60076 (Power transformers - ability to withstand short-circuit), etc. Made of standardized materials, it has the performance of high- and low-temperature resistance
Get the latest price
Quantity Needed:
Pieces
E-mail:


This connector was supposed to be molded in glass-fiber-reinforced,flame-retardant nylon.
It came with size 35X29.5X26mm,with 40pcs pins in center.High rib,hooks and boss on round side.One four cavity mold should employ a mold base dimension 250*230mm,with 280mm height.Steel grade 1.2767 is used for the mold inserts,while grade 1.2312 is employed for mold plates as well as the ejector plate.Steel grade 1.1730 is mused for remaining plate and rails.Thermal insulating plates,which are available in sizes to match the standard mold plates,serve to insulate the mold from the machine platens.
high efficiency electronic parts electronic customized for andon electronics-1
high efficiency electronic parts electronic customized for andon electronics-2



◇◆ Mold design


high efficiency electronic parts electronic customized for andon electronics-3

This part is simple,but need to ensure 40pcs pin locate properly when plastic filling,specially under high pressure flow.To save production cost,we need to cut down cycle time.So two or three even more over-mold inserts need.Injection machine operator no need to set pin one by one into mold.Just need to set in additional insert before molding.When mold open,just need put whole insert with pin into core.Of course,operator need to take part with insert together.The hooks on both sides are undercut,need design for slider or angle lifter.But no slider split line allow in middle surface.So split line should be set on radius of corner.

The molded part is ejected via knockout pins.In addition to providing for ejection.these pins serve to vent the cavity during filling.It is in part for this reason that the knockout pins are located beneath ribs and other deep section of the part.where entrapped air is to be expected.The mold filling pattern during injection of the molding compound as well as the mechanical and thermal aspects of the mold design were simulated and established during the design phase with the aid of appropriate computer programs.



Euromicron Mould injection molded electronics meets mandatory electrical safety requirements. It has to pass the following tests: high voltage test, leakage current test, insulation resistance test, and ground continuity test. Welded carefully, it is scratch-proof and won't hurt people
Euromicron Mould electronic parts is an outcome of four applicable expertise. Specific knowledge in geology, chemical analysis, and high purity process are used to convert raw materials into high purity and high-value final product. It is less likely to leave dents on the product
Euromicron Mould electronic parts is sophisticatedly designed. Our architects and engineers consider many issues when working with the design, including environmental issues, aesthetic appearance, occupant comfort, and view. Having been tested multiple times, it has an increased tightness
The whole production procedures of Euromicron Mould injection molded electronics are in line with hardware manufacture standards both domestically and internationally, including the stamping and welding processes. The product is flame retardant, ensuring maximum safety
Euromicron Mould electronic parts is produced in line with the strict specifications for phone models required by customers. From its materials selection to the size inspection stage, it will be tested by our QC team. The product has the advantages of heavy tension and impact resistance
This product has good strength. Any suddenly applied or impact load which may cause failure has been taken into consideration in the design phase. The center of the product is highly consistent
Product Message
Chat Online 编辑模式下无法使用
Chat Online inputting...