Euromicron Mould Engineering Limited was found in 1995

Euromicron Mould  >  AI - Page Sitemap  >  Euromicron Mould stb plastic enclosure manufacturer for andon electronics
Euromicron Mould stb plastic enclosure manufacturer for andon electronics

Euromicron Mould stb plastic enclosure manufacturer for andon electronics
  • Euromicron Mould stb plastic enclosure manufacturer for andon electronics
  • Euromicron Mould stb plastic enclosure manufacturer for andon electronics
  • Euromicron Mould stb plastic enclosure manufacturer for andon electronics
  • Euromicron Mould stb plastic enclosure manufacturer for andon electronics
  • Euromicron Mould stb plastic enclosure manufacturer for andon electronics

Euromicron Mould stb plastic enclosure manufacturer for andon electronics

This product has an excellent cushioning effect. Thanks to its anatomical arch and supportive layers, it showcases the soft cushioning effect.
Get the latest price
Quantity Needed:
Pieces
E-mail:
Product Details
Euromicron adheres to the principle of 'details determine success or failure' and pays great attention to the details of injection mold.The products we produce are in strict line with the . Their high quality is guaranteed through reliable material sourcing and strict QC methods.Well-chosen in material, fine in workmanship, excellent in quality and favorable in price, Euromicron's injection mold is highly competitive in the domestic and foreign markets.
Product Comparison
cnc service, manufactured based on high-quality materials and advanced technology, has reasonable structure, excellent performance, stable quality, and long-lasting durability. It is a reliable product which is widely recognized in the market.The products we produce are in strict line with the . Their high quality is guaranteed through reliable material sourcing and strict QC methods.Supported by advanced technology, Euromicron has a great breakthrough in the comprehensive competitiveness of cnc service, as shown in the following aspects.
Company Advantages
1. In the production of Euromicron Mould injection moldable plastics , the superior material is applied properly.
2. This product features a clean appearance. Its seam leaves a clean look on the inside of the fabric and does not affect the outside.
3. This product has an excellent cushioning effect. Thanks to its anatomical arch and supportive layers, it showcases the soft cushioning effect.
4. This product is widely used in various applications and has great market potential.
5. The product can be widely applied to different fields.


Euromicron Mould stb plastic enclosure manufacturer for andon electronics-1
Euromicron Mould stb plastic enclosure manufacturer for andon electronics-2


◇◆ Product parameters


Part Name:Electronic connector
Part size:45*39.5*21mm
Raw Material:PA9T30GF
Color:RAL9005,Black
Mould Cavity No.:1*4
Injection gate:Hot runner 
Surface finished: VDI3400-33
Core &Cavity steel:1.2344,hardness 48~52HRC
Mold component standard:HASCO or equivalent
Injection machine size:250T
Cycle time:40S
Mold life:100000 shots
Customer:Bitron
Export:Italy


◇◆ PRODUCT FEATURES
A connector shell was supposed to be molded in glass-fiber-reinforced,flame-retardant nylon.
Euromicron Mould stb plastic enclosure manufacturer for andon electronics-3

This connector include two different parts(upper and lower halves),were to be produced in a single mold.Prior to the start of production,the question arose as to whether a second gate might not be required to fill the part.To avoid weld lines and entrapped air.however,it might also be necessary to use only a single gate.This flexibility as to gating was supposed to be possible simple by switching a hot runner nozzle on or off.A further difficulty resulted from the small amount of space in which  the gates were to be located on the face of the molded part.All of these requirements were satisfied through the particular arrangement of the conductive,internally heated hot-runner system.

Euromicron Mould stb plastic enclosure manufacturer for andon electronics-4

Mold design-We made this mold with four cavity.Runner system consists of a heated sprue bushing,a hot-runner manifold and four hot-runner nozzles.The hot-runner nozzles have not been installed parallel to the longitudinal axis of the mold,but rather at an angle.In spite of the unfavorable geometric relationships,it is possible to gate each part on its face in this manner.This arrangement is possible,because the solidified melt in the outer regions of the hot-runner manifold and nozzle channels precludes any possibility of leakage.Each of the hot-runner nozzle is individually controlled and can thus be switched on or off as required.It is thus possible to fill the part through either on or two gates.These measures alone,however,would not have been adequate to vary the gating possibilities.Attention also have to be given to the hot-runner manifold to ensure that no melt stagnated at continuously high temperatures in the runner channels when the various gating possibility were being employed.




Company Features
1. Euromicron Mould has innovative equipment to manufacture high-quality plastic enclosure .
2. With the help of advanced machines, injection moldable plastics is produced with high efficiency and high quality.
3. Euromicron Mould attaches a great importance to strengthening plastic prototype at all levels, making it more competitive in the industry. Get more info! Euromicron Mould Engineering Limited has made unremitting efforts to create more perfect products and technologies. Get more info! custom plastic box serves as an impetus to help the realization of Euromicron Mould' market goal. Get more info! Euromicron Mould actively carries out considerate service for customers satisfactions. Get more info!
Contact us

 

Product Description

Specifications of Plastic WIFI Router Switch Box

1) Type: Plastic WIFI Router Switch Box

2)Size:120*120*25mm mm

3) Cusomization:color ,cutout,silkscreen,label ,Acrylic sheet

4) Easy and safe to use

5) High moisture resistance and excellent mechanical protection

Euromicron Mould injection moldable plastics is produced using the high-end materials. Easy Use to Maximize Performance
Euromicron Mould injection moldable plastics is produced by using the best raw material and sophisticated technology in complete compliance with the set industry standards. Mayer Pipelines For Myriad Supplies
Euromicron Mould plastic prototype is made of the finest materials that have passed our strict materials selection system. Mayer Pipelines For Myriad Supplies
The advanced technology has been applied throughout the whole production of Euromicron Mould plastic prototype. We Control Pipelines, You Control Health
Euromicron Mould plastic prototype is fabricated using utmost quality raw materials in compliance with the international standards. Health Starts From Every Pipe
Our quality check team strictly controls the quality of this product. Expert of 100% Hygienic Pipelines
Product Message
Chat Online 编辑模式下无法使用
Chat Online inputting...