Euromicron Mould Engineering Limited was found in 1995

Euromicron Mould  > 

AI - Page Sitemap

 > 

Euromicron Mould OEM ODM auto parts factory source now for businessman

Euromicron Mould OEM ODM auto parts factory source now for businessman

Euromicron Mould OEM ODM auto parts factory source now for businessman

Product Name
Auto tank
Product size
495*76*83mm
Material
PA66+30%GF
Cavity
1*2
Cycle time
41S
Customer
Mercedes Benz
Export
Germany
Price
Get Latest Price
Get the latest price
Quantity Needed:
Pieces
E-mail:
Company Advantages
1. Euromicron Mould Engineering Limited insists on using first-class raw material. It is suitable for use in the high-temperature environment
2. When comparing the cost and build time to a traditional home, this product will be less in both of these areas. Its manufacturing meets the international quality standards
3. The product has undergone strict tests according to international quality standards. Its appearance is stylish and creates a stereoscopic sense
4. A full in-house laboratory is available to ensure the consistency and quality of the raw material. Its quality has been certified under ISO14001:2004 and CE


Euromicron Mould OEM ODM auto parts factory source now for businessman-1
Euromicron Mould OEM ODM auto parts factory source now for businessman-2



◇◆ Product Features


Euromicron Mould OEM ODM auto parts factory source now for businessman-3

The product is applied in the automobile Mercedes Benz. It is a part of the tank. It works in the high temperature environment. So it is made of the material PA66 with 30% glass fiber. This is a special heat-resistant material. Also it is a high strength engineering material. This composite materials have superiorities in size stability, formability, stretching resistance and impact resistance. This a long product. The length is 495mm. width is 76mm, height is 83mm. it is easy to deflect after injecting. So it is very important to solve deflect issue in the mold.


Euromicron Mould OEM ODM auto parts factory source now for businessman-4

The mold is a two-cavities design with hot runner system. The valve gate of the hot runner system is directly on the part. We did mold flow analysis before mold design. Through technical analysis, we can estimate the deformation of the part and find some problems of injection molding. So that we saved some steel for late adjustment about deformation.Meanwhile, we did Some preventive measures for possible problems.

Euromicron Mould OEM ODM auto parts factory source now for businessman-5

In this way, we can optimized the mold after trailing shoot until the molding was good. The structure of the part was a lot complex. There were some bosses and hooks at the side of the product. It needed several sliders to formed them. For cooling system, it was very important too. Good cooling system can decrease the deformation of the product and the cycle time. So we designed several sufficient cooling loops for this mold. Not only cooling loops were design in the core insert and cavity insert, but also cooling loops were designed in the sliders and the mold plate.

Euromicron Mould OEM ODM auto parts factory source now for businessman-6

In that case, the temperature of the mold can be controlled well. And the product was very stable. The cycle time was about 41 seconds. By controlling the valves of the hot runner system, we can control the volume of each part and the balance of flowing. Because of the plastic material including 30%glass fiber, the steel of forming insert must be harden steel. We choose to use imported steel 1.2344 which hardness was about 52 HRC. The mold ran well. The mold run over 3 hours for testing before delivery to customer. Customer was satisfied the mold.



Company Features
1. Euromicron Mould Engineering Limited focuses on improvement of technology and R&D.
2. As a defender for auto parts factory, Euromicron Mould Engineering Limited has always insisted on injection auto parts . Inquire!
Product Message
Chat Online 编辑模式下无法使用
Chat Online inputting...