Euromicron Mould Engineering Limited was found in 1995

Euromicron Mould  >  AI - Page Sitemap  >  Euromicron Mould loudspeaker car body molding source now for businessman
Euromicron Mould loudspeaker car body molding source now for businessman

Euromicron Mould loudspeaker car body molding source now for businessman
  • Euromicron Mould loudspeaker car body molding source now for businessman
  • Euromicron Mould loudspeaker car body molding source now for businessman

Euromicron Mould loudspeaker car body molding source now for businessman

Euromicron Mould is good at integrating design, manufacturing and sales car body molding .
Inquire Online
Get the latest price
Quantity Needed:
Pieces
E-mail:
Product Comparison
Euromicron's die casting mold is manufactured in strict accordance with relevant national standards. Every detail matters in the production. Strict cost control promotes the production of high-quality and priced-low product. Such a product is up to customers' needs for a highly cost-effective product.The products we produce are in strict line with the . Their high quality is guaranteed through reliable material sourcing and strict QC methods. die casting mold has the following advantages over other products in the same category.
Application Scope
Euromicron's die casting mold has been widely used in many industries.While providing quality products, Euromicron is dedicated to providing personalized solutions for customers according to their needs and actual situations.The products we produce are in strict line with the . Their high quality is guaranteed through reliable material sourcing and strict QC methods.
Company Advantages
1. car body molding is unusual in design and appropriate in size.
2. The product will always deliver the desired consistency. It is programmed for precise and repetitive motion, which is less likely to make mistakes.
3. This product may be the first time a customer sees a company/brand. It connects customers with the company/brand and impresses them.


This trail mold was used to injection Auto door plastic part in different thermoplastics, such as  PC/ABS blend and modified PA, elastomer-modified PC, PC/PBTP blend and modified PBTTB for a number of manufacturing companies.
The two-cavities mold for Auto door plastic part consists essentially of sprue half with the hot runner system and the ejector mold half. Pillars and bushings serve to guide the two mold halves. When the mold is closed. The mold halves are fixed relative to each other via angled surfaces and wear plates.
Gating and temperature control. The molding compound passes through a sprue bushing into the hot runner made of steel (material number 1.2311). From four heated nozzles, also of steel (material number 1.2162), it passes through cold feed channels to the various gates of the mold cavity. The gates measure 15 mm X 1.2 mm.

Euromicron Mould loudspeaker car body molding source now for businessman-1

The hot runner manifold block is heated by cartridge heaters which are pressed against it by laterally bolted cover strips. The distributor lies in a recess of the feed-side mold plate and is pressed by the hot runner covering plate against the nozzles via spacer rings. Guide components prevent the manifold from twisting about the locating device. They also allow the manifold to expand and contract during heating and cooling. The hot runner nozzles are each centered in their locator bores in mold plate by means of three contact surfaces in such a way that they do not experience the expansion and contraction undergone by the manifold. The contact surfaces facing the manifold are convex. Transfer areas for the molding compound are sealed with steel O-rings. The ends of the hot runner nozzles on the mold side have conical bores. In this region. Their exteriors fit snugly into the mold platen to ensure good thermal conduction and thus rapid cooling of the sprue formed therein.

On mold opening, the frozen sprue separates from the hot melt in the manifold at the narrowest point of the conical bore. The nozzles are heated with heating collars. Two temperature probes are attached to each nozzle to monitor and regulate the temperature. The cartridge heaters in the manifold are arranged in seven groups, each of which is individually regulated. The cartridges have an installed rating of about 40 KW.
The melt pressure in the manifold is registered by pressure sennsor P. and that in the cavity, by sensor P. and cann therefore be used for control purposes. The temperature-control system consists of a network of bores in the two mold hales. Heat sensors T measure the temperature in the mold.
Ejection of the Auto door plastic part
When the mold opens, the molded part remains in the moving half. The sprues are also held in place by sprue pullers above the ejector pins. As soon as the stripper plates are pushed forward by the ejector of the machine, the ejector pins push the molded part along with the sprues from the mold core. On mold closing, the ejector plates and thus also the ejector pins are pushed back by ejector-plate return pins. The mold plate is supported by rolls projecting right through the ejector plates to the clamping plate.



Company Features
1. Euromicron Mould is good at integrating design, manufacturing and sales car body molding .
2. Our company has expert teams. They have the expertise to always make the right decision, retain control, manage risk and guarantee customers consistently high quality products.
3. We have a clear market positioning. We are determined to become the leader in the industry. From now on, we will actively grasp the emerging product concepts and innovative technologies to optimize our products and strengthen our capabilities. We have high-performance work teams. They can execute quickly, make reliable decisions, solve complex problems, and spare efforts to increases company productivity and morale.
Euromicron Mould injection molding in automotive industry will be inspected to guarantee high quality. It will be scrutinized to eliminate the circumstances of skipping stitches, sparse needle pitch, loose thread, floating thread, and break stitches.
There are strict quality requirements for Euromicron Mould car body molding. The product has to pass tests in terms of colorfastness (CF to light, ozone, water, bleach), odor, rigidity, stretchability, and wearing resistance.
The inspections for Euromicron Mould car body molding are conducted based on quality control procedures. These procedures include fabrics, checking, size measurement, sewing, and finishing.
Euromicron Mould car body molding has been tested by third-party labs. It has been tested with regard to longitudinal & torsional stiffness, biomechanical comfort, pressure distribution, slip resistance, and thermal comfort.
Euromicron Mould injection molding in automotive industry is created based on aesthetic principles. They are mainly the beauty of shape, form, workmanship, materials, color, lines, and matching with the space style.
The production of this product adopts the highest quality materials and advanced tools to determine industry principles.
Product Message
Chat Online 编辑模式下无法使用
Chat Online inputting...