Euromicron Mould Engineering Limited was found in 1995

Euromicron Mould  >  AI - Page Sitemap  >  Euromicron Mould high productivity plastic enclosure box supplier for electronic components
Euromicron Mould high productivity plastic enclosure box supplier for electronic components

Euromicron Mould high productivity plastic enclosure box supplier for electronic components
  • Euromicron Mould high productivity plastic enclosure box supplier for electronic components
  • Euromicron Mould high productivity plastic enclosure box supplier for electronic components
  • Euromicron Mould high productivity plastic enclosure box supplier for electronic components
  • Euromicron Mould high productivity plastic enclosure box supplier for electronic components
  • Euromicron Mould high productivity plastic enclosure box supplier for electronic components

Euromicron Mould high productivity plastic enclosure box supplier for electronic components

Euromicron Mould plastic molding manufacturing meets the requirements of a series of standards. These standards include IEC 60038 (IEC standard voltages), IEC 60076 (Power transformers - ability to withstand short-circuit), etc. It is exported to over 30 countries and regions in the world
Inquire Online
Get the latest price
Quantity Needed:
Pieces
E-mail:


This cover is part of an telecom set-top box.
The appearance surface has dimension of 396X56X45mm.There are one round opening ¢35 and one rectangular opening 20X150mm.Also there are many boss and rid in high side.There is undercut on right wall of long side.
Euromicron Mould high productivity plastic enclosure box supplier for electronic components-1
Euromicron Mould high productivity plastic enclosure box supplier for electronic components-2



◇◆ Product Features


Euromicron Mould high productivity plastic enclosure box supplier for electronic components-3
Mold design

We set sprue bushing on round opening,when fill with sub gate from both sides.Ejector sleeve need locate on boss to help release part.Pin or insert for high side rib to help air venting,also for easily manufacture or EMD process.A slider would be need for side undercut.Since all outside surface are visible,no slider split line is allowed.This mean a tunnel slider would be needed on core side.Mold base size would be 600X400mm with height 350mm.The design of the mold provide for simultaneous opening of the two parting lines with the aid of two racks and a pinion for each side.As it is essential that no gate marks show on the front of the molded parts,injection had to take place on the inside.

Euromicron Mould high productivity plastic enclosure box supplier for electronic components-4
Cooling

This cover transfer heat quickly to mold surfaces.so that increased outlay on the cooling system is worthwhile in molds for such parts.Cooling of the core should be given special attention.Also some of the inserts are thin and very high.A beryllium/copper cap with six radial cooing channels is placed on the core insert.These cooling channel require drilling of the center of rube leading to the cap.This drilling weakens the center tube and there is the risk of rupture if the mounting nuts are tightened excessively.Compression spring are provided to permit an exactly defined tightening torque.Coolant is supplied to the cooling channels in the slides via tubes threaded into the slides.Slots in the guide strips allow these tubes to follow the motion of the slides.



Euromicron Mould plastic molding manufacturing meets mandatory electrical safety requirements. It has to pass the following tests: high voltage test, leakage current test, insulation resistance test, and ground continuity test. The product has the advantages of heavy tension and impact resistance
Euromicron Mould plastic molding manufacturing is an outcome of four applicable expertise. Specific knowledge in geology, chemical analysis, and high purity process are used to convert raw materials into high purity and high-value final product. The product is sealed and welded exquisitely
Euromicron Mould plastic molding manufacturing is sophisticatedly designed. Our architects and engineers consider many issues when working with the design, including environmental issues, aesthetic appearance, occupant comfort, and view. It is granted with appearance design patents and utility model patents
The whole production procedures of Euromicron Mould plastic molding manufacturing are in line with hardware manufacture standards both domestically and internationally, including the stamping and welding processes. It is less likely to leave dents on the product
Euromicron Mould plastic molding manufacturing is produced in line with the strict specifications for phone models required by customers. From its materials selection to the size inspection stage, it will be tested by our QC team. It is highly resistant to acid, alkali, and other chemical substances
This product has good strength. Any suddenly applied or impact load which may cause failure has been taken into consideration in the design phase. The product is flame retardant, ensuring maximum safety
Product Message
Chat Online 编辑模式下无法使用
Chat Online inputting...