Euromicron Mould Engineering Limited was found in 1995

Euromicron Mould  >  AI - Page Sitemap  >  Euromicron Mould electrommunication electronic communication equipment wholesale for andon electronics
Euromicron Mould electrommunication electronic communication equipment wholesale for andon electronics

Euromicron Mould electrommunication electronic communication equipment wholesale for andon electronics
  • Euromicron Mould electrommunication electronic communication equipment wholesale for andon electronics
  • Euromicron Mould electrommunication electronic communication equipment wholesale for andon electronics
  • Euromicron Mould electrommunication electronic communication equipment wholesale for andon electronics
  • Euromicron Mould electrommunication electronic communication equipment wholesale for andon electronics

Euromicron Mould electrommunication electronic communication equipment wholesale for andon electronics

This connector was...
Inquire Online
Get the latest price
Quantity Needed:
Pieces
E-mail:
Company Advantages
1. High-tech machines have been applied in the production of Euromicron Mould . It needs to be machined under the molding machines, cutting machines, and various surface treating machines. Vacuum packing method is adopted for the product to avoid mold rusting during transportation
2. The product offered by Euromicron Mould is highly preferred by the customers in the industry for outstanding advantages. Its manufacturing meets the international quality standards
3. To satisfy the needs of our customers, we additionally design the performance which is . It is characterized by a very good surface finish


This connector was supposed to be molded in glass-fiber-reinforced,flame-retardant nylon.
It came with size 35X29.5X26mm,with 40pcs pins in center.High rib,hooks and boss on round side.One four cavity mold should employ a mold base dimension 250*230mm,with 280mm height.Steel grade 1.2767 is used for the mold inserts,while grade 1.2312 is employed for mold plates as well as the ejector plate.Steel grade 1.1730 is mused for remaining plate and rails.Thermal insulating plates,which are available in sizes to match the standard mold plates,serve to insulate the mold from the machine platens.
Euromicron Mould electrommunication electronic communication equipment wholesale for andon electronics-1
Euromicron Mould electrommunication electronic communication equipment wholesale for andon electronics-2



◇◆ Mold design


Euromicron Mould electrommunication electronic communication equipment wholesale for andon electronics-3

This part is simple,but need to ensure 40pcs pin locate properly when plastic filling,specially under high pressure flow.To save production cost,we need to cut down cycle time.So two or three even more over-mold inserts need.Injection machine operator no need to set pin one by one into mold.Just need to set in additional insert before molding.When mold open,just need put whole insert with pin into core.Of course,operator need to take part with insert together.The hooks on both sides are undercut,need design for slider or angle lifter.But no slider split line allow in middle surface.So split line should be set on radius of corner.

The molded part is ejected via knockout pins.In addition to providing for ejection.these pins serve to vent the cavity during filling.It is in part for this reason that the knockout pins are located beneath ribs and other deep section of the part.where entrapped air is to be expected.The mold filling pattern during injection of the molding compound as well as the mechanical and thermal aspects of the mold design were simulated and established during the design phase with the aid of appropriate computer programs.



Company Features
1. Euromicron Mould Engineering Limited primarily manufactures a wide range of electronic communication equipment to meet customer's various needs. Euromicron Mould has great technical power to guarantee the quality of electronic parts .
2. With the application of technology, the quality assurance of overmolding electronics has been greatly improved.
3. Let Euromicron Mould build and manage a team of professionals for your business. is both our motto and goal. Call!
The colors of overmolding electronics is various. Manufactured by strict quality control, each mattress is highly recommended
The production of Euromicron Mould overmolding electronics has been completed by advanced and efficient equipment. JLH products have passed CFR 1633 and BS 7177
Euromicron Mould electronic communication equipment conforms to the product design specifications. Each spring is sealed in a strong fiber bag to prevent mould or insects effectively
Unique design ideas make electronic parts more practical. Hand-tufted mattress is good enough that could be rolled and compressed in a box
Euromicron Mould electronic parts leads the industry in the progress of production. Each spring is sealed in a strong fiber bag to prevent mould or insects effectively
Products are tested by our quality experts in strict accordance with a series of parameters to ensure the quality and performance. JLH Mattress offers the professional OEM and ODM service for you
Product Message
Chat Online 编辑模式下无法使用
Chat Online inputting...