Euromicron Mould Engineering Limited was found in 1995

Euromicron Mould  >  AI - Page Sitemap  >  Euromicron Mould by plastic prototype supplier for electronic components
Euromicron Mould by plastic prototype supplier for electronic components

Euromicron Mould by plastic prototype supplier for electronic components
  • Euromicron Mould by plastic prototype supplier for electronic components
  • Euromicron Mould by plastic prototype supplier for electronic components
  • Euromicron Mould by plastic prototype supplier for electronic components

Euromicron Mould by plastic prototype supplier for electronic components

Euromicron Mould plastic enclosure for electronic products is developed by a research and development team who are familiar with the combinations and formulas of different fabrics and dyes. It is perfect for wedding and event favors, resort vacation keepsakes, souvenirs, etc
Inquire Online
Get the latest price
Quantity Needed:
Pieces
E-mail:


Part Name:Electronic connector
Part size:18*15*3mm
Raw Material:NYLON+30%GF
Color:RAL9005,Black
Mould Cavity No.:16+16
Injection gate:Cold runner 
Surface finished: Polishing #600
Core &Cavity steel:1.2344, hardness 48~52HRC
Mold component standard:DME or equivalent
Injection machine size:120T
Cycle time:18S
Mold life:300000 shots
Customer:AEC
Export:USA


◇◆ Summary for project running
This product used for electrical connector. And was supposed to be molded in glass-fiber-reinforced, flame-retardant nylon.
Euromicron Mould by plastic prototype supplier for electronic components-1

There are many small pin holes on part. Hole’s diameter is 0.6mm with 2.2mm distance of each. Dimension tolerance should be within +/-0.01mm.   Mold design-We will make this mold with 2+2cavity, cold runner in to banana gate. To make parts leave on core side, parting line should be on top. And all pin holes location need to be inserted. Because the hole diameter and distance need to keep in strict tolerance. Separated insert make it easy to replace. Need to pay high attention to electrode making and EDM process. We made whole electrode include all pin holes position, then checked by CMM machine, until shown it was made in proper dimension, took to Mirror EDM manufacture.

Euromicron Mould by plastic prototype supplier for electronic components-2

Injection-Any mismatch or flash in switch(female half) hole would cause male half pin bend, so this request holding pressure not too high. but also guarantee not cause sink mark on outside surface. Although the part and mold is small, enough cooling line still necessary. Because the part quantity in demand is one million each month, we need to cut down cycle time as much as possible. So that we can save production cost.




Euromicron Mould plastic enclosure for electronic products has passed many teats. These tests are internal and external pressure resistance, mechanical strength, life cycle analysis, etc. Its materials are non-toxic, which is especially important for kids
Euromicron Mould plastic prototype has proper design and engineering. It is an outcome of our qualified architects, designers, and structural engineers using their aptitude. Its materials are stiff, hard and have a low moisture content, resulting in a good quality puzzle
Euromicron Mould plastic enclosure for electronic products has been certified according to some key certificates. These certificates mainly include national compulsory product certification (CCC), IEC electrical safety standards, etc. It features excellent picture quality and lasting color
Euromicron Mould plastic enclosure for electronic products materials have been tested to eliminate any chemicals that have a negative impact on health. The finished work can be hung in the game room, workshop, garage, bar, etc
Euromicron Mould plastic enclosure for electronic products has passed the test, which is characterized by its design that promotes heat and moisture outflow from the body. It is perfect for wedding and event favors, resort vacation keepsakes, souvenirs, etc
Strict testing: its current performance has been tested by third parties. It is also ready to be tested by users and will be continuously updated. It can be used to boost skills: hand-eye coordination, motor skills, problem-solving, etc
Product Message
Chat Online 编辑模式下无法使用
Chat Online inputting...